Error codes of mini loaders Bobcat will help you identify the faulty actuator and quickly repair the failed mechanism of both internal combustion engine and hydraulic system
| Code | Description |
|---|---|
| 01-16 | Air filter not connected |
| 01-17 | Clogged air filter |
| 02-16 | No hydraulic discharge filter is connected |
| 02-17 | Clogged Hydraulic Discharge Filter |
| 03-09 | Low battery voltage |
| 03-10 | High Voltage battery |
| 03-11 | Extremely high battery voltage |
| 03-14 | Extremely low battery voltage |
| 03-22 | The battery voltage is below the maximum permissible |
| 04-09 | Low oil pressure in the engine |
| 04-14 | Extreme hHibiscus oil pressure level in the engine |
| 04-15 | Engine oil pressure at emergency shutdown level |
| 04-21 | The oil pressure in the engine is above the maximum permissible |
| 04-22 | The oil pressure in the engine is below the maximum permissible |
| 05-09 | Low recharge pressure in the hydraulic system |
| 05-14 | Extremely low recharge pressure in the hydraulic system |
| 05-15 | Recharge pressure in the hydraulic system at the level of emergency shutdown of the engine |
| 05-21 | The recharge pressure in the hydraulic system is higher than the maximum |
| 05-22 | The recharge pressure in the hydraulic system is below the maximum permissible |
| 06-10 | High engine speed |
| 06-11 | Extremely high engine speed |
| 06-13 | No engine speed signal |
| 06-15 | Engine speed at the emergency shutdown level |
| 06-18 | Engine speed outside the permissible limits |
| 07-10 | High oil temperature in the hydraulic system |
| 07-11 | Extremely high oil temperature in the hydraulic system |
| 07-15 | Oil temperature in the hydraulic system at the level of emergency shutdown of the engine |
| 07-21 | The oil temperature in the hydraulic system is higher than the maximum permissible |
| 07-22 | The oil temperature in the hydraulic system is below the maximum permissible |
| 08-10 | High temperature of engine coolant |
| 08-11 | Extremely high engine coolant temperature |
| 08-15 | Engine coolant temperature at the emergency shutdown level |
| 08-21 | The coolant temperature of the engine is above the maximum permissible |
| 08-22 | The coolant temperature of the engine is below the maximum permissible |
| 09-09 | Low fuel level |
| 09-21 | The fuel level is above the maximum permissible |
| 09-22 | The fuel level is below the maximum permissible |
| 11-05 | The safety frame sensor is closed to the battery |
| 11-06 | The security frame sensor is closed to mass |
| 12-21 | Signal PWM Controller front additional. Hydraulics at the upper limit of the range |
| 12-22 | PWM Controller front additional. Hydraulics at the lower limit of the range |
| 12-23 | PWM Controller front additional. Hydraulics are not in a neutral position |
| 13-05 | The retaining solenoid of the fuel cutoff is closed on the battery |
| 13-06 | The retaining solenoid of the fuel cutoff is closed to the mass |
| 13-07 | Circuit Break solenoid cutoff fuel |
| 14-02 | Motorcyclist the fuel cutoff solenoid, erroneous switching on |
| 14-03 | Motorcyclist the fuel cutoff solenoid, erroneous shutdown |
| 15-02 | Motorcyclist solenoid lock thrust, erroneous inclusion |
| 15-03 | Motorcyclist solenoid lock thrust, erroneous shutdown |
| 16-05 | The holding solenoid lock is closed on the battery |
| 16-06 | The holding solenoid of the thrust lock is closed to the mass |
| 16-07 | Tearing chain restraint solenoid lock thrust |
| 17-05 | The hydraulic valve solenoid is closed to the battery |
| 17-06 | The hydraulic valve solenoid is closed to the mass |
| 17-07 | Rupture of the solenoid circuit of the hydraulic shutoff valve |
| 18-05 | The spool solenoid is closed on the battery |
| 18-06 | The spool solenoid is closed to the mass |
| 18-07 | Spool solenoid circuit break |
| 19-02 | Bucket positioning solenoid, erroneous switching on |
| 19-03 | Bucket positioning solenoid, erroneous shutdown |
| 20-02 | Speed switching solenoid, erroneous switching on |
| 20-03 | Speed switch solenoid, erroneous shutdown |
| 21-02 | Glow plugs, erroneous inclusion |
| 21-03 | Glow plugs, erroneous shutdown |
| 22-02 | Starter, erroneous inclusion |
| 22-03 | Starter, erroneous shutdown |
| 23-02 | Rear base solenoid, erroneous switching on |
| 23-03 | Rear base solenoid, erroneous shutdown |
| 24-02 | Rear Pull Solenoid, erroneous switching on |
| 24-03 | Rear Pull Solenoid, erroneous shutdown |
| 25-02 | Rear auxiliary proportional solenoid, erroneous inclusion |
| 25-03 | Rear auxiliary proportional solenoid, erroneous shutdown |
| 26-02 | Erroneous inclusion of the front base solenoid |
| 26-03 | Erroneous shutdown of the front base solenoid |
| 27-02 | Erroneous inclusion of the front Stock Solenoid |
| 27-03 | Erroneous shutdown of the front Stock Solenoid |
| 28-02 | Erroneous inclusion of solenoid Divertera |
| 28-03 | Incorrect solenoid shutdown Divertera |
| 29-02 | Large feed solenoid, erroneous switching on |
| 29-03 | Large feed solenoid, erroneous shutdown |
| 30-28 | Controller memory failure |
| 31-28 | Recovery mode failure |
| 32-04 | Advanced Management (ACS) is not reported to the controller Bobcat |
| 32-23 | ACS Advanced Management Not calibrated |
| 32-31 | Failure of the actuating mechanism of inclination |
| 32-32 | Malfunction of the electrical wiring of the actuating mechanism of inclination |
| 32-33 | Failure of the electrical wiring of the bucket tilting handle |
| 32-34 | Executive tilting mechanism not in neutral position |
| 32-35 | Handle/Bucket tilt pedal not in neutral position |
| 32-36 | Failure of the actuating mechanism of lifting |
| 32-37 | Malfunction of electrical wiring of the actuating mechanism of lifting |
| 32-38 | Failure of the electrical wiring of the boom handle |
| 32-39 | Executive lifting mechanism not in neutral position |
| 32-40 | Arm/Boom lift pedal not in neutral position |
| 32-41 | No connection |
| 32-49 | Executive lifting mechanism closed to mass |
| 32-50 | The executive tilting mechanism is closed to mass |
| 32-51 | Actuator lifting mechanism closed on the battery |
| 32-52 | The actuator tilting mechanism is closed to the battery |
| 32-53 | Handle/Boom lift pedal closed to mass |
| 32-54 | Handle/Bucket tilt pedal closed to mass |
| 32-55 | Arm/Boom lift pedal closed on battery |
| 32-56 | The handle/bucket tilt pedal is closed to the battery |
| 32-57 | Reduced performance of the lifting actuation mechanism |
| 32-58 | Reduced performance of the executive tilt mechanism |
| 32-59 | Wrong direction of the actuating mechanism of lifting |
| 32-60 | Wrong direction of the executive tilt mechanism |
| 32-61 | The lock of arms is closed to mass |
| 32-62 | The lock of Arms is closed on the battery |
| 32-63 | The chain of locking pedals is closed to the mass |
| 32-64 | The chain of locking pedals is closed to the battery |
| 32-65 | Sensor supply voltage outside the permissible limits |
| 32-66 | Battery voltage out of the allowable limits |
| 32-67 | Switched during Operation |
| 32-68 | Boom Boom ARM Information error |
| 32-69 | The switch of control modes has switched during operation |
| 32-70 | The chain of the right handle of motion is closed to mass |
| 32-71 | Circuit of the right handle of movement is closed on the battery |
| 33-23 | Main controller (Controller Bobcat) Not programmed |
| 34-04 | The keypad with a button run is not reported to the controller Bobcat |
| 35-02 | Speed fan switch, erroneous switching on |
| 35-03 | Speed fan switch, erroneous shutdown |
| 36-48 | Multiple ACD controllers are connected |
| 37-02 | Speed additional speed switch, erroneous switching on |
| 37-03 | Speed additional speed switch, erroneous shutdown |
| 38-04 | No connection to Joystick controller |
| 38-05 | The x-axis of the left joystick is not in a neutral position |
| 38-06 | The X-axis of the right joystick is not in a neutral position |
| 38-07 | The Y-axis of the left joystick is not in a neutral position |
| 38-08 | The Y-axis of the right joystick is not in a neutral position |
| 38-09 | Control mode switch-circuit to the battery or to the mass |
| 38-11 | Executive lifting mechanism not in neutral position |
| 38-12 | Executive tilting mechanism not in neutral position |
| 38-13 | Failure of the actuating mechanism of lifting |
| 38-14 | Failure of the actuating mechanism of inclination |
| 38-15 | Right Wheel speed control failure |
| 38-16 | Faulty wiring for the speed of the left wheel |
| 38-17 | Reduced performance of the executive tilt mechanism |
| 38-18 | Reduced performance of the lifting actuation mechanism |
| 38-19 | The X-axis of the left joystick, behind the upper bound of the range |
| 38-20 | X-axis of the right joystick, beyond the lower bound of the range |
| 38-21 | The Y-axis of the left joystick, behind the upper bound of the range |
| 38-22 | The Y-axis of the right joystick, behind the upper bound of the range |
| 38-23 | Signal of the front right control sensor outside the upper boundary of the range |
| 38-24 | Signal of the front left control sensor at the upper limit of the range |
| 38-25 | Signal of the rear right control sensor at the upper limit of the range |
| 38-26 | Signal of the rear left control sensor at the upper limit of the range |
| 38-27 | Signal of the actuating mechanism of lifting at the upper boundary of the range |
| 38-28 | Signal of the executive mechanism of inclination at the upper boundary of the range |
| 38-29 | X-axis of the left joystick, behind the lower bound of the range |
| 38-30 | X-axis of the right joystick, beyond the lower bound of the range |
| 38-31 | Y-axis of the left joystick, beyond the lower bound of the range |
| 38-32 | Y-axis of the right joystick, beyond the lower bound of the range |
| 38-33 | Signal of the front right control sensor at the lower limit of the range |
| 38-34 | Signal of the front left control sensor at the lower limit of the range |
| 38-35 | Signal of the rear right control sensor at the lower limit of the range |
| 38-36 | Signal of the rear left control sensor at the lower limit of the range |
| 38-37 | Power supply "1" 5-volt sensor, behind the lower boundary of the range |
| 38-38 | Power supply "2" 5-volt sensor, behind the lower boundary of the range |
| 38-39 | Executive lifting mechanism closed to mass/beyond the lower boundary of the range |
| 38-40 | The executive tilt mechanism is closed to the mass/signal at the lower limit of the range |
| 38-41 | Wrong direction of the executive tilt mechanism |
| 38-42 | Wrong direction of the actuating mechanism of lifting |
| 38-43 | The solenoid of the left front drive, erroneous switching on |
| 38-44 | Solenoid of left reversible drive, erroneous switching on |
| 38-45 | Right front drive solenoid, erroneous switching on |
| 38-46 | Right reverse actuator solenoid, erroneous switching on |
| 38-47 | Front right control solenoid, erroneous switching on |
| 38-48 | Front left solenoid control, erroneous switching on |
| 38-49 | Rear right control solenoid, erroneous switching on |
| 38-50 | Rear left solenoid control, erroneous switching on |
| 38-51 | Control system pressure solenoid, erroneous switching on |
| 38-52 | Reversing signal, erroneous switching on |
| 38-53 | Left Front drive solenoid, erroneous shutdown |
| 38-54 | Solenoid of left reversible drive, erroneous shutdown |
| 38-55 | Right front drive solenoid, erroneous shutdown |
| 38-56 | Right reverse actuator solenoid, erroneous shutdown |
| 38-57 | Front right extension control solenoid, erroneous shutdown |
| 38-58 | Front right retraction control solenoid, erroneous shutdown |
| 38-59 | Front left solenoid of extension control, erroneous shutdown |
| 38-60 | Front left solenoid control retraction, erroneous shutdown |
| 38-61 | Rear right extension control solenoid, erroneous shutdown |
| 38-62 | Rear right retraction control solenoid, erroneous shutdown |
| 38-63 | Rear left solenoid control, erroneous shutdown |
| 38-64 | Rear left solenoid control retraction, erroneous shutdown |
| 38-65 | Control system pressure solenoid, erroneous shutdown |
| 38-66 | Reversing signal, erroneous shutdown |
| 38-67 | No messages from controller Bobcat |
| 38-68 | Wheel setting angles (alignment) not calibrated |
| 38-69 | actuating mechanisms of lifting and tilting are not calibrated |
| 38-70 | Power off |
| 38-71 | Battery voltage outside the permissible limits |
| 38-72 | Drive Pump Not calibrated |
| 38-73 | Control/Motion mode switch is switched on during operation |
| 38-74 | Speed of the uncontrolled right wheel, erroneous switching on |
| 38-75 | Speed of uncontrolled left wheel, erroneous switching on |
| 38-76 | Control system pressure solenoid-insufficient current |
| 38-77 | Front right extension control solenoid-insufficient current |
| 38-78 | Front right retraction control solenoid-insufficient current |
| 38-79 | Forward left solenoid of extension control-insufficient current |
| 38-80 | Front left solenoid control retraction-insufficient current |
| 38-81 | Rear right extension control solenoid-insufficient current |
| 38-82 | Rear right retraction control solenoid-insufficient current |
| 38-83 | Rear left solenoid control-insufficient current |
| 38-84 | Rear left solenoid control retraction-insufficient current |
| 38-85 | Power supply "1" 5-volt sensor outside the upper boundary of the range |
| 38-86 | Power supply "2" 5-volt sensor outside the upper boundary of the range |
| 38-87 | Right front wheel lock (mechanical malfunction control) |
| 38-88 | Locking of the Left front wheel (mechanical malfunction control) |
| 38-89 | Right rear wheel lock (mechanical malfunction control) |
| 38-90 | Rear left control error |
| 38-91 | There are no pulses of the right wheel speed sensor |
| 38-92 | There are no pulses of the left wheel speed sensor |
| 38-93 | Right wheel speed sensor does not respond |
| 38-94 | The left wheel speed sensor does not respond |
| 38-98 | Controller in the drive calibration mode |
| 38-99 | Controller in wheel position calibration mode |
| 45-03 | Right turn pointer, erroneous shutdown |
| 46-02 | Left turn pointer, erroneous inclusion |
| 46-03 | Left turn pointer, erroneous shutdown |
| 47-21 | Power supply of 8-volt sensor at the upper limit of the range |
| 47-22 | Power supply of 8-volt sensor, behind the lower boundary of the range |
| 48-02 | Front light relays, erroneous switching on |
| 48-03 | Front light relay, erroneous shutdown |
| 49-02 | Rear light relay, erroneous switching on |
| 49-03 | Rear light relay, erroneous shutdown |
| 60-21 | Signal of the control lever of the back additional Hydraulics at the top of the range |
| 60-22 | Signal of the control lever of the back additional Hydraulics at the lower limit of the range |
| 60-23 | Control lever of the back additional The hydraulics are not returned to the neutral position |
| 64-02 | Failure to turn on the power relay |
| 64-03 | Erroneous shutdown of power relay |
| 74-72 | Controller boot code failed Bobcat |
| 74-73 | Left panel, receiving device error |
| 80-02 | ACD, Exit "A", erroneous switching on |
| 80-03 | ACD, Exit "A", erroneous shutdown |
| 81-02 | ACD, Output "B", erroneous switching on |
| 81-03 | ACD, Exit "B", erroneous shutdown |
| 82-02 | ACD, Exit "C", erroneous inclusion |
| 82-03 | ACD, Exit "C", erroneous shutdown |
| 83-02 | ACD, Exit "D", erroneous switching on |
| 83-03 | ACD, Exit "D", erroneous shutdown |
| 84-02 | ACD, Output "E", erroneous switching on |
| 84-03 | ACD, Exit "E", erroneous shutdown |
| 90-02 | Service exit "C", erroneous switching on |
| 90-03 | Service exit "C", erroneous shutdown |
| 91-02 | Service exit "D", erroneous switching on |
| 91-03 | Service exit "D", erroneous shutdown |
| 92-02 | Service exit "E", erroneous inclusion |
| 92-03 | Service Output "E", erroneous shutdown |
| 93-02 | Service exit "F", erroneous switching on |
| 93-03 | Service exit "F", erroneous shutdown |